Відео

Could I use it on my welds after welding patch panels on my truck and then apply body putty over top of it? How about on the welds of my floor board after welding in the new floorboard? I am trying to ensure no water seeps through the porosity of the butt welds.

This is impressive guys good to see the tests that get run on these, the last 4 TJ's i have overhauled have all put in lord packers.

Ise remove karna ho to kaise karen

What is the joint strength

Le quitaron los amortiguadores al normal , salta a la vista para alguien que sepa un poco sobre vehiculos

You should have taped off and covered the roof rails before cutting roof off for for replacement!!

thanks for your lesson, it's very helpful

How good does this adhesive hold against moisture and heat?

SolarPack to the moon!

Tengo el pegamento chemikol que deluyente puedo hechar

Where to buy gun?

As a aircraft mechanic, I found that fascinating to watch the manuevers and how the engine mount handled.it.Thank you very much for sharing this.

epdm rubber past glue any available clear

Hi. Interesting video. Thanks. I need to bond EDMI to stainless steel. The bond does not need to be permanent. Just long enough to wiggle it over a tube. I have a 3” exhaust clamp that’s 360 degrees. It’s 3” in diameter and 3” thick. My EDMI rubber sheet is 1/16th inch thick. I want to put it on the inside surface of the clamp. This will be wrapped around a 3” diameter steel pipe. The rubber is so the clamp doesn’t scar the surface of the pipe. What bonding agent and surface prep should I use? Thanks, Paul

Music adds NOTHING to tech videos. Jump cuts don't either. More views would sell more product. Do better. Your audience are SKILLED people and training videos should reflect that.

Chemlok 607 sería para anclaje de caucho con metal previamente granallado?

Apa tersedia perekat lnflatable seal gasket silicone

Very nice summary, thanks for sharing.

Where can I buy this ?

best

This is so interesting; I look forward to my tour of CAVS!

como limpio la brocha que se utilizo con esa pintura? con que solvente???

Great overview of design flexibility for adhesives. Welding and auto-body bonding is vital with the "LORD" technology for all transportation-vehicles. Thanks! T J (Tom) Vanderloop, Author, Technology Instructor & Consultant

Great Video on adhesives and standard operating procedures. Great tips for OEM-auto repair. T J (Tom) Vanderloop, Author, Technology Educator & Manufacturing Consultant (AWS & SME-Member)

Is that pink stuff Silicon grease?

Is it 810/20GB product

Excellent talk, enjoyed the humor

Very informative. Thanks

P 205 220 One Litter each

U r agent dealer in jaipur

Me servira para cofeccionar calzos para motor de autos o sea bulganizar goma con inserto metalicos

Really unfortunate that this recording focuses almost entirely on the presenter and not the slides. If you like hearing someone describe what the audience is seeing in their slide deck without actually seeing the slides you’ll love this.

What are you nailing into on the table?

Thanks for this video. I have dug a hole in the dirt down to bedrock for a water pond. So I want to line the side of the hole with concrete leaving the bedrock exposed. Therefore the concrete must bond to the rock at the bottom and seal the sides of the hole to prevent water from leaking from the pond. Is this possible? What product should I use? Are the product(s) available in Mexico?

How to remove this if any wrong installation done

How fast does it cure into a workable putty?

Single coating metal to rubber bonding is possible...Bonding strength is high or low compare to double coating process...

What are the benefits over 8560? Is 8560 replaced by 8566?

necesito un pegamento para pegar las bobinas de las bocinas en conos de polipropileno cual me recomiendas

Chloroform gun name please?

plier name please?

Hi! Sir I moulding silicon spoon and we use iron rod inside but problem is chemlock 608, chemlock 7 not working. Starting 608 work well but after 30 days it not sticking with silicon

Thanks

There’s no way that’s structurally sound. A solar array anchor point on a roof shingle? 😹

Dr Onyeneke on UA-cam is a man of his words he truly assured me that my thyroid will be a forgotten issue once I get his herbal medicine today I can not feel any thyroid anymore I am healed from my thyroid God bless you sir I will make sure people if possible the entire universe hear about your great herbal medicine and it healing miracle.

Nice animation... Which software did you used to animate and model?

Gracias por estos videos tan importantes para los profesionales y emprendedores de anuncios luminosos. Si desean un letrero nosotros los fabricamos en México con estos pegamentos www.suitprint.com

Nice!! Enjoying your channel! You should use PromoSM! I used it to promote my Instagram and it helped my posts start to trend. It could really help you promote your videos too!!